BMW 5 Series E39

1. Open a cowl.

2. Turn to the left against the stop the holder of a lamp of passing beam (1) and take out it.

3. Take out a lamp and replace it.
4. Establish the holder of a lamp of passing beam and turn it to the right against the stop.
5. Turn to the left against the stop the holder of a lamp of driving beam (2) and take out it
6. Rasstykuyte shtekerny connection.
7. Establish the new holder of a lamp with a lamp on a connector and record it.
8. Establish the holder of a lamp of driving beam and turn to the right against the stop.

1. Turn to the left against the stop the holder of a lamp of parking light (3) and take out it.

2. Take out a lamp and replace it.

3. Insert into the case the holder of a lamp a big pad upward and turn to the right.

1. Squeeze the holder of a lamp for pads and take out him back.
2. Slightly press a lamp in the holder, turn on the left and take out.
3. Insert a new lamp, press it in the holder, turn to the right and record.
4. Press the holder of a lamp and record him.

1. Press a lamp fingers at a back edge forward and take out.
2. Turn a lamp on the left, having slightly pressed and take out.
3. Slightly press on a new lamp, turn to the right and record it.

1. Remove a clip of a decorative lattice. For this purpose take out a pin (2), then a clip (1).

2. Disconnect a decorative lattice above and take out it.
3. Take out a cover near a fog light forward.

3. Turn out 2 two bolts of fastening and take aside a fog light.

4. Press a spring (1) from a reverse side in the direction of an arrow on an accompanying illustration.

5. Hook a cover (2) on the one hand and disconnect it with another.

6. Disconnect a spring clip (1) from the holder (2).

7. Uncover contacts and replace a lamp.
8. Fix a new lamp by a clip.
9. Check a condition of laying (3) in a cover, if necessary replace.
10. Insert a cover, press it and fix by a spring clip.
11. Insert a fog light and fix it by screws.
12. Fix a decorative lattice, press a clip and record it razzhimny pins.

1. Open a trunk lid.
2. Remove side facing.

3. Turn on 90 ° clip (1) to the left and remove the holder of a lamp (2).

4. Slightly press a lamp in the holder, turn to the left and take out.

5. Insert a new lamp, press it a little in the holder, turn to the left and record.

6. Establish the holder of a lamp and turn a clip.

1. Open a trunk lid.
2. Remove the screw-driver a black plastic cover from the lower party of a hanger under headdresses.
3. Turn the holder of a lamp to the left and take out him.
4. Insert a new lamp, having pressed it a little in the holder, turn to the right and record.
5. Establish the holder of a lamp and fix, having turned to the right.
6. Fix a plastic cover from the lower side of the shelf under headdresses.

1. Insert the screw-driver into a cut and press to the right, as shown an arrow; lamp will leave fastening.

2. Remove a lamp and replace a lamp

1. Main lamp. Squeeze out a plafond, having hooked it sideways the screw-driver, and remove glass then take a lamp from contact holders.
2. Lamp of individual lighting. Take out a lamp, having slightly pressed on it and having turned to the left

1. Squeeze out a plafond, having hooked it the screw-driver, having inserted into dredging from above
2. Main lamp. Having wrung out a uvula on a reflector, replace a lamp
3. Lamp of individual lighting. Take out a lamp, having slightly pressed on it and having turned to the left

1. Remove lamp glass, having hooked it sideways the screw-driver
2. Replace a lamp

1. Squeeze out a lamp, having hooked it the screw-driver inserted into dredging
2. Remove a reflector
3. Replace a lamp

1. Squeeze out a lamp, having hooked it the screw-driver inserted into dredging
2. Remove a reflector
3. Replace a lamp