BMW 5 Series E39

since 1996-2001 release

Repair and operation of the car



BMW E39
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the finishing panels manufactured of vinyl
   Care of an upholstery and rugs of salon
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and installation of a cowl
   Adjustment of provision of a cowl
   Removal and installation of a trunk lid
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Replacement of a slip/company inscription
   Removal, installation and adjustment of a door
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of the power window
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a front seat
   Seat belt tension device
   Security measures at the handling of the belt tension device
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and installation of the shelf under a headdress
   Removal and installation of blinds of back glass
+ Onboard electric equipment
+ Schemes of electric equipment
+ System of onboard diagnostics


64a8d164


Removal and installation of a front seat

If the electric drive of adjustment of longitudinal provision of a seat has malfunction, see the Instruction at the end of the present Section.


 REMOVAL

1. Establish a seat vertically and shift it completely forward.

2. Turn out the screw of fastening of a seat belt.

3. Take away a stopper (1) back and take out it inside. Take out the drive of adjustment of height of a belt (2) forward.

4. Turn out internal peaks upward (1). For this purpose unclench a clip. Take out it in the middle of (2) upward and remove (3) back.

5. Rasstykuyte shtekerny connection (2), having opened a stopper (1).

6. Turn out back bolts.

7. Displace a seat completely back.

8. Electric drive of adjustment of a seat: Open a cover (A) forward. Open (1) stopper (V) and a rasstykuyta shtekerny connection (2).

9. Turn out forward bolts.

If the seat is transported, removed or long time remains removed, block a natyazhitel of a seat belt, address the Section Protection of the Device of a Tension of a Belt.


 INSTALLATION

1. Establish a seat.

The rug has to be in the region of points of fastening of screws, but not between guides of a seat and a bottom leaf. Otherwise at the movement of the car there can be an extraneous noise.

2. Fix a seat by new bolts. At first behind, then in front. Do not tighten fastening bolts.

If old bolts are applied, before installation grease them with means for fixing of threaded connections of LOCTITE 270.

 

3. Fix bolts by the moment of 40 Nanometers in the sequence: forward internal, forward external, back internal, back external.
4. Electric drive of adjustment of a seat: Put a seat completely back, join shtekerny connection and record it. Establish a cover.
5. Connect multiposition shtekerny connection and record it.
6. Fix peaks.
7. Connect an adjustment drive cable on height and record it.
8. Fix a seat belt below by the moment of 50 Nanometers.

Only at malfunction of the electric drive of adjustment of longitudinal provision of a seat

 PERFORMANCE ORDER

1. Remove a peak of an internal guide of a seat.
2. Install the mechanism of adjustment of an inclination of a seat in the top situation.
3. Disconnect the plug from the pump if it is available.
4. Turn off two bolts of fastening of a forward guide of a seat and overturn a seat back.
5. Turn out two bolts of fastening of the electric drive of adjustment of longitudinal provision of a seat and remove the drive.
6. Press the switch of adjustment of longitudinal situation.
7. Adjustment does not work: Attach the new drive and turn on it. If now adjustment works, reducer is serviceable. It is necessary to replace only the electric drive.
8. The electric drive works, SEAT does not move: The reducer is faulty. Replace it.
9. Rasstykuyte shtekerny connection of longitudinal adjustment of a seat.
10. Cut a connecting shaft.
11. Turn off two nuts of fastening and remove a reducer at the left and on the right. After that the seat can be displaced a hand.
12. Fix by bolts the directing seats (only for removal).
13. Remove a seat and replace guides with new.